DFI Lanparty UT NF3-250Gb s754 adventures

[eva2000]

Preordered from mittoni.com.au this board weeks ago and finally 2 days ago it arrived :D

Full Pics here (http://www.fileshosts.com/AMD/DFI/6002_650/web/)

http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_01_thumb.jpg (http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_01.html) http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_06_thumb.jpg (http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_06.html) http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_11_thumb.jpg (http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_11.html) http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_17_thumb.jpg (http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_17.html) http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_18_thumb.jpg (http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_18.html) http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_33_thumb.jpg (http://www.fileshosts.com/AMD/DFI/6002_650/web/DFI_250Gb_33.html)

System
AMD64 3400+ Newcastle cooled with MCW6002 + MCP650 Pump
DFI Lanparty UT NF3-250Gb s754 revA 14/09/04 bios
64MB Albatron MX480EL testing
1x 256MB KHX3200K2/512 BH-5 testing
120GB WD 1200JB
Yamaha CD-RW Burner
550W Antec TrueControl

Notes

1. Swiftech MCW6002 waterblock's screws aren't the right size - too short with the springs or too long without springs and won't fit the DFI stock retention bracket. I had to place a thin pad of foam under the backplate underside of board to position the backplate flush against the back side of motherboard, then use the DFI stock retention bracket's screws by themselves to securely fasten the MCW6002 waterblock

2. board came with 27/8/04 bios - which reported my AMD64 3400+ Newcastle cpu in bios as CPU Idle = 56-59C! Updated to 14/09/04 bios and bios now reports CPU Idle = 44-46C, while in windows reports 39-42C idle - still 10-13C above my idle temps on my Shuttle AN50R!

3. chipset heatsink is warm even with the fan you see over it on zalman fan bracket even with stock chipset voltage = 1.6v. Using infra-read thermometer under load, chipset heatsink measures 31-36C with 28C room temps at stock 2411mhz on cpu.

4. cpu:ram dividers to the max :cool:

ram dividers
1:1
1:2
3:5
2:3
7:10
3:4
5:6
9:10

-----------------
temps reported by Speedfan

stock speed @ 12x200.9mhz = 2411mhz
vcore idle = 1.472v
vcore load (stresscpu) = 1.52-1.536v

CPU idle = 39-42C
CPU load (stresscpu) = 52-56C

i believe cpu temps are at least 10-14C over reported as my same cpu on Shuttle AN50R had cpu idle = 25-30C and cpu load = 40-42C

my 12v rail is rock steady at 12.09v with 550W Antec TrueControl

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/200-200-2226-1T-1.5-2.8-1.6-1.55/stresscpu_load_speedfan1.jpg

----------------
Update:
multipliers from in bios work fine and stable! This is at 10x 240HTT, 1.5v vcore, 3.0vdimm and vAGP and vChipset = AUTO and mem timings 2-2-2-6 with CPC = AUTO and all other timing settings at AUTO

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/10x/240-240-2226-1T-1.5-3-1.5-1.55/cpuz_idle.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/10x/240-240-2226-1T-1.5-3-1.5-1.55/mem-buff.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/10x/240-240-2226-1T-1.5-3-1.5-1.55/mem-unbuff.jpg

I guess unbuffered is low due to the AUTO set values for rest of memory timings are very loose! This is what A64Tweaker reports for those values i set as AUTO in bios - very loose compared to what AN50R board has according to A64Tweaker.

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/10x/240-240-2226-1T-1.5-3-1.5-1.55/a64tweaker_AUTO.jpg

AN50R when 2-2-2-6 1T was set, reported in A64Tweaker something like 2-10-12-2-2-6-2-2-3-2-2


.

[malinois1]

Hey Eva Think you could post some PcMark04--02----also 3Dmarkscores--and sandra cpu arithemetic? I know I am asking alot :D but I am very interested in that board and setup. Also how do you think it compares to the rig in my sig in real world performance? Thanks mate :thumb:

P.S. BTW I have never had an AMD system always intel so not sure if I want to make the switch. Well I guess not really a switch. I could keep the one I like the best I guess and give the other to the kids and sell the kids 1.8G P4 :idea: LOL The wife will kill me if she hears this.

[LostInSpace278]

I am very interested in this board my self. I reall need something better than the GA-K8VNXP, it only allows for 2.7 vdimm :(

[eva2000]

3dmark with MX480EL lol fun hehe

well here's where i am at the moment with this board not 100% stable still figuring it out but.... :D

AMD64 3400+ Newcastle @ 11x 245HTT = 2695mhz at 1.55v + 113% = 1.7515v (1.744v idle)
DFI Lanparty UT NF3-250Gb 14/09/04 bios
1x 256MB KHX3200K2/512 BH-5 @ 245mhz 2-2-2-6 1T at 3.1v
Win2K SP4

Swiftech MCW6002 + MCP650 Pump
Heatercore with 2x 120x38mm Panaflo 103cfm fans

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/11x/245-245-2226-1T-10-12-1.75-3.1-1.5-1.6/pifast_tweak-8-12-2-2-1-1_all.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/11x/245-245-2226-1T-10-12-1.75-3.1-1.5-1.6/superpi-1m_tweaked.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/11x/245-245-2226-1T-10-12-1.75-3.1-1.5-1.6/superpi-8m_tweaked.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/11x/245-245-2226-1T-10-12-1.75-3.1-1.5-1.6/cpu.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/11x/245-245-2226-1T-10-12-1.75-3.1-1.5-1.6/mem-buff-tweaked.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/1x256/10/LDT_AUTO/11x/245-245-2226-1T-10-12-1.75-3.1-1.5-1.6/mem-unbuff-tweaked.jpg


Still windows cpu temps are over reported by at least 10-14C.... CPU temp = 43-46C idle and 56-62C load!

[eva2000]

quick results no screenies yet still benching but

i'm at 10x 260HTT with 1:1 ram @260mhz 2-2-2-6 at 3.28v on this board now :)

Sandra 2004 Pro SP2b
Buffered = 4033/4036 MB/s
Unbuffered = 2428/2484 MB/s

SuperPi
1M = 33s
2M = 1min 17s
4M = 2min 51s
8M = 6min 30s

Everest Home
Read = 4037 MB/s
Write = 1721 MB/s

Hexus Pifast = 47.11s

Memtest86+ v1.26 = 1953 MB/s bandwidth

[eva2000]

10x 260HTT = 2600mhz at 1.525v + 110% vcore (haven't tried lower yet)
2x 256MB KHX3200K2/512 BH-5 @ 260mhz 2-2-2-6 1T at 3.28v (set CPC as AUTO)

set in bios

8-12-2-2-2-2
R/W Queue Bypass = 16x
Max Bypass = 7x

everthing else AUTO

this is what is shown

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/2x256/10_11/LDT_AUTO/10x/260-260-2226-1T-8-12-2-2-2-2-7x-16x-1.66-3.3-1.5-1.6/a64tweaker_original.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/2x256/10_11/LDT_AUTO/10x/260-260-2226-1T-8-12-2-2-2-2-7x-16x-1.66-3.3-1.5-1.6/cpuz1.jpg

Pifast = 47.09s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/2x256/10_11/LDT_AUTO/10x/260-260-2226-1T-8-12-2-2-2-2-7x-16x-1.66-3.3-1.5-1.6/pifast.jpg)

As you can see vcore idle = 1.648v and load = 1.712-1.728v hehe
http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200K2/2x256/10_11/LDT_AUTO/10x/260-260-2226-1T-8-12-2-2-2-2-7x-16x-1.66-3.3-1.5-1.6/stresscpu_1.jpg

[eva2000]

1x 256MB XMS3500C2v1.1 BH-5

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Corsair/XMS3500C2/256/1x256/0033026_30811604/LDT_AUTO/9x/270-270-2226-1T-1.55-3.54-1.5-1.8/cpuz_tweaked.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Corsair/XMS3500C2/256/1x256/0033026_30811604/LDT_AUTO/9x/270-270-2226-1T-1.55-3.54-1.5-1.8/mem-buff_tweaked.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Corsair/XMS3500C2/256/1x256/0033026_30811604/LDT_AUTO/9x/270-270-2226-1T-1.55-3.54-1.5-1.8/mem-unbuff_tweaked.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Corsair/XMS3500C2/256/1x256/0033026_30811604/LDT_AUTO/9x/270-270-2226-1T-1.55-3.54-1.5-1.8/pifast_twk.jpg

-------------------------------------
1x 512MB KHX3200/512 BH-5 using cpu:mem dividers and AUTO timings

Newcastles max HTT with dividers seems to be lower than Clawhammer cpus

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/6x/372-248-2226-1T-1.5-3.46-1.5-1.7/cpuz.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/6x/372-248-2226-1T-1.5-3.46-1.5-1.7/mem-buff.jpg

[eva2000]

1x 512MB OCZ PC3700EB

@ 265mhz 3-3-2-8 at 2.8v with chipset = 1.6v
@ 270mhz 3-3-2-8 at 3.0v with chipset = 1.7v
@ 275mhz 3-3-2-8 at 3.1v with chipset = 1.7v
@ 280mhz 3-3-2-8 at 3.32v with chipset = 1.8v
@ 285mhz 3-3-2-8 at 3.43v with chipset = 1.8v

Holy crap look at this

AMD64 3400+ @ 9x 285 = 2565mhz at 1.525 + 10% vcore
DFI Lanparty UT NF3-250Gb 14/09/04 bios
1x 512MB OCZ PC3700EB @ 285mhz 3-3-2-8 1T at 3.43v via OCZ DDR Booster
120GB WD 1200JB
550W Antec TrueControl PSU

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/OCZ/PC3700EB/1x512/single/1/LDT_AUTO/9x/285-285-3328-1T-1.66-3.43-1.8_DS2/cpuz.jpg

Sandra 2004 PRO SP2b
Buffered = 4413 / 4412 (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/OCZ/PC3700EB/1x512/single/1/LDT_AUTO/9x/285-285-3328-1T-1.66-3.43-1.8_DS2/mem-buff_3328-11-13-2222_spd.jpg)
Unbuffered = 2591 / 2659 (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/OCZ/PC3700EB/1x512/single/1/LDT_AUTO/9x/285-285-3328-1T-1.66-3.43-1.8_DS2/mem-unbuff_3328-11-13-2222_spd.jpg)

Hexus Pifast = 47.94s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/OCZ/PC3700EB/1x512/single/1/LDT_AUTO/9x/285-285-3328-1T-1.66-3.43-1.8_DS2/pifast_3328-11-13-2222.jpg)

SuperPi
1M = 34s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/OCZ/PC3700EB/1x512/single/1/LDT_AUTO/9x/285-285-3328-1T-1.66-3.43-1.8_DS2/superpi-1m_11-13-2222.jpg)
2M = 1min 18s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/OCZ/PC3700EB/1x512/single/1/LDT_AUTO/9x/285-285-3328-1T-1.66-3.43-1.8_DS2/superpi-2m_11-13-2222.jpg)

[Governator]

Hi, new to DFI and the forums here, could you please tell me where all of these new BIOSs, betas or otherwise are found? Thanks!

[teddy07x]

I ran 260 FSB 1:1 divider@cas2.5-3-3-7 with OCZ platinum rev2.

here is what I found out,
The ONLY stable VDIMM is 2.9. Don't even try 3 or 3.1. It's not stable, not even if you raise the rails on psu to give it more juice.

I was running 8x260, and 9x260 with stock volt on vcore.
(raising the vcore wouldn't only make the computer boot under load because of lack of cooling on cpu)

the memory on 2.9 volts won't do any more than 230-235. boot yes, but burn in and other benches would reboot it if any over that.

So what do I have? I have chips that are rock stable on 225 and 220 fsb with tight timings. I have a cpu that can do 2.3 ghz and still be stable and cool.

I tried 220x10.5 and 225x10, neither are stable. under load the frickn thing just crashes. I'm running tight timings 2-2-2-11. as 11 is best for gaming and 3dmark.

the FSB doesn't seem to be any problem.
I tried 3.1 vdimm on 220x10.5 no luck.

I swapped the SATA ports and that helped me alot.

do you guys know why I won't get it stable on 220-225x10/10.5.

what is normal temp on a 3400+ Clawhammer btw?

[eva2000]

latest beta bios at http://www.dfi-street.com/forum/forumdisplay.php?s=&forumid=22 sticky thread at top

teedy07x, what bios and psu you're using ?

fyi, OCZ PC3200 plat rev2 doesnt like high volts, optimal speed of ram will be at 2.8-2.9v and 2x 512MB will lessen max oc than say 2x 256MB or 1x 512MB or 1x 256MB

[eva2000]

Well how about this, after some tweaking managed to get 1x 512MB Kingston HyperX KHX3200/512 BH-5 rock stable @ 260mhz 2-2-2-6 1T at 3.54v vdimm

with 9800Pro Extreme some 3dmarks

3dmark2001 = 25,698 (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/3dmark2001_9800pro_480-402_25698.jpg) | http://service.futuremark.com/compare?2k1=8175322
3dmark2003 = 7,737 (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/3dmark2003_9800pro_483-402_7737.jpg) | http://service.futuremark.com/compare?2k3=3233916
3dmark05 = 3,167 (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/3dmark05_9800pro_483-402_3167_session.jpg) | http://service.futuremark.com/compare?3dm05=153295
Pcmark04 = 5,221 (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/pcmark04_483-402_5221.jpg) | http://service.futuremark.com/compare?pcm04=2618975
Aquamark3 = 59,477 (http://arc.aquamark3.com/arc/arc_view.php?run=1692184156)

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/mem-buff1.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/mem-unbuff1.jpg

Hexus PiFast = 46.97s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/pifast.jpg)

SuperPi
1M = 33s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/superpi-1m.jpg)
2M = 1min 17s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/superpi-2m.jpg)
4M = 2min 52s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/superpi-4m.jpg)
8M = 6min 13s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/superpi-8m.jpg)
16M = 14min 24s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/superpi-16m.jpg)
32M = 38min 41s (http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/10x/260-260-2226-1T-9-12-2211-1.66-3.54-1.5-1.7_DSlvl1_7x16x_3120/superpi-32m.jpg)

[PaternityTest]

this board rocks completed 3dmark @260x10 with an a64 3000 and single stick of eb3700@3v "auto timings will tweak harder when get slk-948u and fortron 530 psu"

[jhatfie]

I had to return my first board for RMA. It is a long story but after many, many, many hours of troubleshooting I was not able to run anything 3D related without freezing, crashing or black screens with my DFI LanpartyUT 250GB. Tried 3 graphics cards (9800 Pro, ti4200 and 6800nu), two power supplies (OCZ Powerstream 520W, Enermax Noisetaker 470W), 4 sets of ram including OCZ PC3500EB, Geil Ultra Platinum PC3500, two CPU's, all new cables, two different hard drives in several configurations including RAID0 and RAID1 and no RAID, a dozen windows installs with every driver known to man, 1000 different bios settings enabling and disabling, 3 different bios's. All components work fine on my other A64 motherboards just fine. Should get my replacement Wednesday and we'll see then.

[PaternityTest]

that sucks hopefuly next one wont have that issue...i have a lanparty b also and the ut250gb has a much better quality feel to it uses better capacitors...i was hoping to issues like yours avoided....gopod luck and then happy hunting

[jhatfie]

Just got my new DFI and it works great so far. None of the problems my other one had. Testing with it right now.

[eva2000]

New 3700+ 1MB cache cpu plugged into DFI NF3 250Gb. Seems DFI's temp sensor is reporting cooler temps fro 3700+ than my 3400+ Newcastles. New cpu idles at 31C and 47C load.

AMD64 3700+ 1MB cache
ADA3700AEP5AR
CAAXC 0434RPAW

@1.55v + 113% vcore in bios

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/14_13/LDT_AUTO/225-225-2226-1T-1.75-3.1-1.5-1.6/clockgen/9-12-2211-16x-7x-6ns_200mhz158/pifast_45-20.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/14_13/LDT_AUTO/225-225-2226-1T-1.75-3.1-1.5-1.6/clockgen/229_twk/superpi-2m_twk.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/14_13/LDT_AUTO/225-225-2226-1T-1.75-3.1-1.5-1.6/clockgen/229_twk/cpu.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/14_13/LDT_AUTO/225-225-2226-1T-1.75-3.1-1.5-1.6/superpi-1m_twk.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/14_13/LDT_AUTO/225-225-2226-1T-1.75-3.1-1.5-1.6/cpu.jpg

Very promising cpu indeed :D

[eva2000]

here's where i am with 2x 256MB KHX3200K2/512 BH-5 at stock 1.5v vcore with this cpu on DFI = 2569mhz stresscpu + running 8m superpi at same time

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/10_11/LDT_AUTO/10x/256-256-2226-1T-1.5-3.2-1.5-1.6_9-12-2211-16x-7x-200mhz156/stresscpu_superpi8m_1.jpg

[MarcusOCZ]

That's a nice 3700 there. A friend of mine just got a 3700 from Monarch that won't even do 2.7 on a Mach II at any voltage. The cpu's can be very different it seems.

[eva2000]

yeah this 3700+ is a nice oc'er just need to stabilise the water cooling stuff :)

but

9800pro @ 478/401 = 26,416 3dmark2001
http://service.futuremark.com/compare?2k1=8203042

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/11x/246-246-2226-1T-1.81-3.28-1.6-1.8_10-13-2222-8x-4x_3120/3dmark2001_9800pro_478-401_26416_9-12-2212-8x-4x-3120.jpg

Aquamark3 = 59,668
http://arc.aquamark3.com/arc/arc_view.php?run=14800738

3dmark2003 = 7,754
http://service.futuremark.com/compare?2k3=3281403

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/11x/246-246-2226-1T-1.81-3.28-1.6-1.8_10-13-2222-8x-4x_3120/3dmark2003_9800pro_478-401_7754_9-12-2212-8x-4x_3120.jpg

[WInston]

Could u run central brain identifier for me and take a screen shot?

Tryin to find out which version of the 3700's are any good, if there's a pattern or not?

[eva2000]

cbi ??? HUH ? cpu stepping and date in my sig ;)

[WInston]

http://cbid.amdclub.ru/html/images/cpus/a643200CG1.gif

PLease get it here (http://cbid.amdclub.ru/files/cbid73b.zip)

[eva2000]

awesome app there, i'll try it out too :)

add in a collapseable and expandable tab to the bottom to show memory SPD and timings and you'll have a nice app :D

[WInston]

Any chance of that pic plz eva?

[eva2000]

Any chance of that pic plz eva?

just uploaded it and was about to post them :D

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/200-200-2226-1T-1.5-2.9-1.5-1.6_10-13-2222-dsLVL1_3120/cbi_1.jpg http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/200-200-2226-1T-1.5-2.9-1.5-1.6_10-13-2222-dsLVL1_3120/cbi_2.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/200-200-2226-1T-1.5-2.9-1.5-1.6_10-13-2222-dsLVL1_3120/cbi_2mem.jpg http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/200-200-2226-1T-1.5-2.9-1.5-1.6_10-13-2222-dsLVL1_3120/cbi_3.jpg

http://www.fileshosts.com/AMD/DFI/6002_650/3700/Kingston/KHX3200K2/2x256/3_4/LDT_AUTO/200-200-2226-1T-1.5-2.9-1.5-1.6_10-13-2222-dsLVL1_3120/cbi_4.jpg

[WInston]

:thumb:

[Overcrash86]

what is your MAX FSB ?
mine is :

http://perso.wanadoo.fr/overcrash86/Overcrash86/3000+%2064/DFI%20NF3%20LP%20UT%20250Gb/FSB441.JPG

[eva2000]

with Newcastle 3400+ i maxed HTT at 6x 372HTT booted in via bios no clockgen!

http://www.fileshosts.com/AMD/DFI/6002_650/3400_2/Kingston/KHX3200/1x512/2/LDT_AUTO/6x/372-248-2226-1T-1.5-3.46-1.5-1.7/supepi-2m_vdd1.8.jpg

Haven't tried with my 3700+ yet i expect 400+ HTT though

[nVmatrix]

Anyone running CH5 chips with this board?