1KW PC Power & Cooling SLI power supply tests [Archive]

View Full Version : 1KW PC Power & Cooling SLI power supply tests

eva2000

02-08-2006, 12:03 AM

1KW PC Power & Cooling SLI (http://www.pcpowercooling.com/products/viewproduct.php?show=TC1KW) power supply has arrived. I purchased it from http://www.pccasegear.com.au/prod2484.htm :rock:

Pictures: http://fileshosts.com/psu/PCPowerCooling/1KW/html/

http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_007.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_007.JPG) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_009.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_009.JPG) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_012.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_012.JPG) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_014.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_014.JPG) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_022.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_022.JPG) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_023.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_023.JPG)
Fan used is rated at 0.42amps and is quieter than either fans used in 650W Silverstone SLI or 510W PC Power & Cooling SLI psus :)
Unfortunately, rails are NOT adjustable externally, but with 1KW psu i doubt you would need to adjust them
It came with two adaptors, a 24pin to 20pin and a 8pin to 4pin. Also included is 4 psu case screws as well as a 1KW powered by PC Power & Cooling case sticker/badge.
The box it came in was huge with dimensions of 42cm x 38cm x 23cm :eek:
Apparently each 1KW unit is tested using a Chroma 8000 ATE machine. You can see the report at http://www.pcpowercooling.com/pdf/TC1KW_report.pdf

Highlights:

* 1KW Continuous (1.1KW Peak) @ 50°C
* Fits Std. ATX Cases (20” min. depth)
* +12VDC Rails Total 66A (70A Peak)
* High Efficiency with .99 Power Factor
* Ultra-Tight Regulation (+VDC @ 1%)
* Amazingly Quiet Cooling System
* Complete Array of Output Connectors
* EPS12V, SLI, and SSI Compatibility
* 5-Year Warranty; Unbeatable Support

Specs:
Typo guess continuous = 1000W :)

http://fileshosts.com/psu/PCPowerCooling/1KW/specs.jpg

Dimensions and connectors:
Only down side is only 1xfdd connector, if you use DFI NF4 and SLI and need to use the fdd power connector, then you'd need an adaptor for powering a floppy drive if you have one (which i still use a floppy drive).

http://www.pcpowercooling.com/products/assets/TC1KW/dim_TC1KW.jpg

Test 1 - standalone psu
With 92x38mm sunon 120cfm (13W) + 80x25mm sunon 50cfm (4.3W) fan attached, digital multimeter read rails as

http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_026.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_026.html) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_027.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_027.html) http://fileshosts.com/psu/PCPowerCooling/1KW/html/thumbnails/thumb_1kw_psu_028.JPG (http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_028.html)

3.3+ = 3.397v
5+ = 5.09v
12+ = 12.24v

Test 2 - in below system

Opteron 148 CABYE 0543FPMW @2200mhz stock
Corsair Hydrocool 200EX
512mb HIS X1800XT
4x 80GB Hitachi 7K80 SATA II raid 0
1x 250GB Maxtor Maxline Plus2 PATA
LiteOn 165H DVD-ROM
FDD

http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_031.JPG http://fileshosts.com/psu/PCPowerCooling/1KW/html/photos/1kw_psu_032.JPG

Digital multimeter read the rails as

IDLE:
3.3+ = 3.364v
5+ = 5.06v
12+ = 12.19v

LOAD: CPU Burn K7 ran for 10mins

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/200-200-2.5336-7-22-2223-1.38-1.3-1.5-2.85_3684_ds7dds2/1kw_loadtest_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/200-200-2.5336-7-22-2223-1.38-1.3-1.5-2.85_3684_ds7dds2/1kw_loadtest.jpg)

Forgot to measure the rails with multimeter so will redo the test :bonk:

Okay retested under load but @3014mhz at 1.536v

Digital multimeter read

3.3+ = 3.353v
5+ = 5.05v
12+ = 12.19v

Windows showed

Stressprime
http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/274-274-2.5336-7-22-2223_1.56-1.4-1.6-2.9_3684_ds7dds2_8F55/stressprime_1KWload_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/274-274-2.5336-7-22-2223_1.56-1.4-1.6-2.9_3684_ds7dds2_8F55/stressprime_1KWload_1.jpg)

CPU Burn K7
http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/274-274-2.5336-7-22-2223_1.56-1.4-1.6-2.9_3684_ds7dds2_8F55/cpuburnK7_1KWload_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/274-274-2.5336-7-22-2223_1.56-1.4-1.6-2.9_3684_ds7dds2_8F55/cpuburnK7_1KWload_1.jpg)

Conclusion:
- Well 12+ rail is rock solid and didn't budge according to MBM5 or digital multimeter readings.
- 5+ rail dropped (0.6%) from 4.97v to 4.94v under load in MBM5 and 0.01v drop (0.198%) according to multimeter from 5.06v to 5.05v.
- 3+ rail dropped (0.615%) from 3.25v to 3.23v in MBM5 and dropped (0.327%) from 3.364v to 3.353v from multimeter readings.
- If you take into a/c all 3 rails that's ~0.405% fluctuation on average of 3.3+, 5+ and 12+ rails according to MBM5 or average fluctuation of ~0.175% according to digital multimeter read out. That is within the rated specs of 1% ultra-tight regulation claimed by PC Power & Cooling if you take MBM5 or the multimeter readings :)
- Real test will be when i use phase change, dual core cpu oc'd and SLI or CF video cards oc'd :)

.

eva2000

02-08-2006, 01:57 AM

Further load testing this time Opteron 148 @3102mhz at 1.6v with HIS X1800XT @756/900 with GPU = 1.45v (1.48v) running 3dmark05 with MBM5 running in background.

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/282-282-2.5336-7-20-2223_1.62-1.5-1.6-2.9_3684_ds7dds2_8F55/X1800XT_Maze4/cat62b/3dmark05_756-900_11305_1kwpsu_load_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/282-282-2.5336-7-20-2223_1.62-1.5-1.6-2.9_3684_ds7dds2_8F55/X1800XT_Maze4/cat62b/3dmark05_756-900_11305_1kwpsu_load.jpg)

MBM5 results see:
3.3+ = drop from 3.25v to 3.23v (0.615%)
5+ = drop from 4.97v to 4.94v (0.603%)
12+ = drop from 12.27v to 12.14v (1.06%)

Digital multimeter read the 12+ rail as:

LOAD:
12+ = at start of 3dmark05 drops from 12.19v to 12.16v and stays steady at 12.16v throughout the GT1, GT2 and GT3 tests and then jumps back up to 12.18v for cpu tests in 3dmark05.

So for GT1-GT3 = 0.247% drop and CPU tests = 0.082% drop.

eva2000

02-08-2006, 02:42 AM

PCmark05 load test

@3102mhz at 1.632v
HIS X1800XT @756/900 gpu = 1.45v (1.48v)

PCmark05 = 5,847
http://service.futuremark.com/compare?pcm05=265260

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/282-282-2.5336-7-20-2223_1.62-1.5-1.6-2.9_3684_ds7dds2_8F55/pcmark05_5847_756-900_1kw_loadtest_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron148/CABYE_0543FPMW/HC200EX/Gskill/PC4400LE/2x512/799_800/1114_3/LDT3x/11x/282-282-2.5336-7-20-2223_1.62-1.5-1.6-2.9_3684_ds7dds2_8F55/pcmark05_5847_756-900_1kw_loadtest.jpg)

MBM5 results see:
3.3+ = drop from 3.25v to 3.23v (0.615%)
5+ = drop from 4.97v to 4.94v (0.603%)
12+ = drop from 12.27v to 12.14v (1.06%)

Digital multimeter read the 12+ rail as:

LOAD:

Break down of multimeter read low points for 12+ rail while running Pcmark05

HDD - XP Startup = 12.19v
Physics and 3D = 12.18v
Transparent Windows = 12.17v
3D - Pixel Shader = 12.16v
Web Page Rendering = 12.19v
File Decryption = 12.19v
Graphics Memory - 64 Lines = 12.17v
HDD - General Usage = 12.19v

Multithreaded Test 1 / Audio Compression = 12.19v
Multithreaded Test 1 / Video Encoding = 12.19v

Multithreaded Test 2 / Text Edit = 12.19v
Multithreaded Test 2 / Image Decompression = 12.19v

Multithreaded Test 3 / File Compression = 12.19v
Multithreaded Test 3 / File Encryption = 12.19v
Multithreaded Test 3 / HDD - Virus Scan = 12.19v
Multithreaded Test 3 / Memory Latency - Random 16 MB = 12.19v

As you can see largest dip comes into play when X1800XT needs to do some work :)

Snafu

02-08-2006, 03:14 AM

Very cool results - wow!
:yikes:

eva2000

02-08-2006, 03:43 AM

thanks..... should swap to my Opteron 170 dual core to stress the psu more :D

eva2000

02-08-2006, 08:05 AM

Well swapped back to my Opteron 170 0546XPMW dual core cpu to test this 1KW psu even more and looks good so far :D

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/260-260-3325-8-18-2223_1.33-1.2-1.5-2.64_1552_ds8dds2_8N5/superpi-32m_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/260-260-3325-8-18-2223_1.33-1.2-1.5-2.64_1552_ds8dds2_8N5/superpi-32m.jpg)

RotorHead

02-08-2006, 08:13 AM

Slap the GTX's on that bad boy :D :D

Hawk

02-08-2006, 08:35 AM

Damn, that's a whole lotta juice. . . . :rock: :rock: :rock: :beer:

eva2000

02-08-2006, 11:09 AM

yup alot of juice

dual stressprime @2600mhz at 1.312v, the 12+ rail via multimeter reads 12.19v steady guess the only time the 12+ rail will drop down is when X1800XT needs to work.

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/260-260-3325-8-18-2223_1.33-1.2-1.5-2.64_1552_ds8dds2_8N5/stressprime_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/260-260-3325-8-18-2223_1.33-1.2-1.5-2.64_1552_ds8dds2_8N5/stressprime_1.jpg)

eva2000

02-09-2006, 02:24 AM

PSU seems to run very cool indeed, measured the temp of the air coming out of the psu via the fan and only 37-39C temps in 28-30C room ambients :)

More testing at 2750mhz and 2800mhz dual core at 1.536v and still 12v rail is at 12.19v steady as a rock according to multimeter

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/275-275-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/275-275-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1.jpg)

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/280-254-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/280-254-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1.jpg)

2853mhz at 1.536v is till 12.19v multimeter steady :)

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/285-259-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/285-259-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1.jpg)

eva2000

02-09-2006, 04:06 AM

I can definitely say this psu helps squeeze out more for cpu clocks on my Opteron 170 0546XPMW. Before 2800-2850mhz was best dual prime stable with 2900-2950mhz max benchable. There's no way i could do 2883mhz at 1.536v dual prime stable for even 30 seconds before with 510W PC Power & Cooling SLI psu or 650W Silverstone SLI psu.

And look at where it is right now with multimeter still reading 12v rail as 12.19v rock steady :woot:

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/288-262-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/288-262-3325-8-18-2223_1.56-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1.jpg)

At this rate I maybe able to achieve 3ghz dual core benchable :D

glorfy

02-09-2006, 04:54 AM

Nice :thumbs: I'm green with envy!

eva2000

02-09-2006, 05:44 AM

thanks mate

No way in hell could i even dual prime @2900mhz at 1.6v before until i got this 1KW psu

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1_tnn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.3-1.5-2.64_1552_ds8dds2_8N5/stressprime_1.jpg)

eva2000

02-09-2006, 07:37 AM

well looks like X1800XT @810/963 is the only thing to move this 1KW psu's 12v rail significantly...

did a few 3dmark05 runs @2900mhz at 1.6v with X1800XT @810/963 and 12v drops from 12.19v to 12.15v or 0.328% according to multimeter measurements!

3dmark05 = 12,111 single card

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/295-268-3325-8-18-2223_1.65-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark05_810-963_12111_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/295-268-3325-8-18-2223_1.65-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark05_810-963_12111.jpg)

X1900XT Crossfire or 2x 512MB 7800GTX SLI oc'd would definitely give this psu a nice load to test!

eva2000

02-10-2006, 02:00 PM

well this is what my 6.2 betas do for my X1800XT powered by 1KW psu

3dmark06
@810/963 = 5,914
http://service.futuremark.com/compare?3dm06=119666

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark06_810-964_5914_tnn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark06_810-964_5914.jpg)

@810/981 = 5,930
http://service.futuremark.com/compare?3dm06=119726

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark06_810-981_5930_tnn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark06_810-981_5930.jpg)

6.2beta vs 5.13 at near same clocks
http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark06_5930vs5472_tn.jpg (http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron170/CCWBE_0546XPMW/OCZ/PC4000EB/2_1/1114_3/LDT3x/10x/1KW/180/290-263-3325-8-18-2223_1.62-1.5-1.6-2.64_1552_ds8dds2_8N5/X1800XT_Maze4/3dmark06_5930vs5472.jpg)

Also got a reply from PCP&C folks regarding distribution of the 3x 12+ rails:

Hello George,
On our Turbo-Cool 850 and Turbo-Cool 1KW supplies +12V1 & +12V2 are for the processors and +12V3 is for everything else.

Thanks,
James Dickinson
PC Power & Cooling
V: (760) 931-5700
F: (760) 931-6988

Guess that explains why cpu stress loading has rock steady 12+ rails as they're from +12V1/V2 while X1800XT under load is shared off +12V3's 36amp rated rail.