Prommy Mach2 Adventures Part 1 - 5 [pics]

[eva2000]

Was taking so many pics i ran out of batteries so have to take the rest tomorrow LOL

I'll be spending sometime reading up on how to use the Dremel I got along with the Prommy manuals first but here's some pics

Part 1 - http://fileshosts.com/prometiaMach2/1/

Part2
Small Pics - http://fileshosts.com/prometiaMach2/2/small/
Large Pics - http://fileshosts.com/prometiaMach2/2/large/

Part 3 - http://fileshosts.com/prometiaMach2/3/

Part 4 - Green LED display + Lian Li kit completed! :cool:
http://fileshosts.com/prometiaMach2/4/

Part 5 - http://fileshosts.com/prometiaMach2/5/

http://fileshosts.com/prometiaMach2/1/mach2_0003.JPG

http://fileshosts.com/prometiaMach2/1/mach2_0023.JPG

http://fileshosts.com/prometiaMach2/1/mach2_0026.JPG

http://fileshosts.com/prometiaMach2/1/mach2_0033.JPG

http://fileshosts.com/prometiaMach2/1/mach2_0035.JPG

http://fileshosts.com/prometiaMach2/1/mach2_0052.JPG

[eva2000]

Well i'm uploading Part 2 pics of me taking apart the Prommy unit for the Lian Li kit and will update the first post soon :)

I decided to test the prommy on the bench for now with it stripped bare as i just realised once you put the Lian Li kit on, there is practically nothing to grip or to leverage to lift/carry the unit to it's final destination = my room.

Also the side panels would have sharp edges underside so carry it would be hard - maybe can use the fan mould stuff to cover the bottom side panel's sharp edges too ?

While test fitting the Lian Li front bezel, I realised you actually fit a 120x38mm fan (without the grill) in between the bezel and the radiator - which would be great for additional cooling ?

http://fileshosts.com/prometiaMach2/2/small/mach2_0128.JPG

Part2
Small Pics - http://fileshosts.com/prometiaMach2/2/small/
Large Pics - http://fileshosts.com/prometiaMach2/2/large/

In the nude :)

http://fileshosts.com/prometiaMach2/2/small/mach2_0062.JPG

Hmm the 120mm fans are wired into one plug.. making it harder to replace the fans :(

http://fileshosts.com/prometiaMach2/2/small/mach2_0060.JPG

[eva2000]

more picies

Part 3 - http://fileshosts.com/prometiaMach2/3/

http://fileshosts.com/prometiaMach2/3/mach2_0001.JPG

http://fileshosts.com/prometiaMach2/3/mach2_0009.JPG

the tools :)

http://fileshosts.com/prometiaMach2/3/mach2_0007.JPG

http://fileshosts.com/prometiaMach2/3/mach2_0017.JPG

[eva2000]

Part 4 - Green LED display + Lian Li kit completed! :cool:
http://fileshosts.com/prometiaMach2/4/

Hardest part has to be trying to align the top 2 rails.. messed up on one and had to use a screwdriver to pry the rail off and restick it :o

http://fileshosts.com/prometiaMach2/4/mach2_0018.JPG

http://fileshosts.com/prometiaMach2/4/mach2_0043.JPG

http://fileshosts.com/prometiaMach2/4/mach2_0045.JPG

[Jojo1971]

***drool***

[eva2000]

Glad you like :)

I just installed my P4C800-E into the modded tray http://fileshosts.com/prometiaMach2/3/ and it turns out 2 of the 4 sides need 1cm more cut out :o

Guess I'll do that tomorrow :)

[eva2000]

Well i went ahead and used my Dremel to cut the PC60 bottom hole anyway and finally finished the case modding - did the 4 bolt drill holes for 2nd time but haven't checked if they align yet.

Part 5 - http://fileshosts.com/prometiaMach2/5/

http://fileshosts.com/prometiaMach2/5/mach2_0006.JPG

http://fileshosts.com/prometiaMach2/5/mach2_0029.JPG

1st attempt at tray cutting
http://fileshosts.com/prometiaMach2/5/mach2_0001.JPG

2nd attempt at tray cutting
http://fileshosts.com/prometiaMach2/5/mach2_0048.JPG

Using the included Lian Li conversion kit template for 4 bolt holes is really messed up... this is how the case aligns using the template :rolleyes:

http://fileshosts.com/prometiaMach2/5/mach2_0020.JPG